Our Process

  • Overview

    Professional Bathtub Refinishers Association
    We do the job in one in one day with no mess and no hassles! Here is an example of the steps involved in a typical job.

    • Remove caulking between tub & tile

    • Set up ventilation system if the unit is occupied/thoroughly cover work area other exposed areas /drop cloths & plastic

    • Chemically clean tub/ remove all oils/ body soap/ dirt and grime.

    • Remove waste and overflow cover (when possible) we do not remove the drain unless it is included in the estimate

    • Remove any of the old porcelain glaze still left leaving it dull and ready to prime.

    • We repair most chips 100% free with special patching compound.

    • Sand /blend patched areas/sterilize to remove contamination.

    • Areas are masked off including the floor and any areas that may have been missed when we first arrived.

    • Set-up hot turbine air unit/exhaust system

    • Bonding agent applied to porcelain/permanently fuses the glaze to the porcelain.

    • Two coats Primer applied.

    • Four part glaze topcoat mixed/ applied.

    • Tub is sprayed giving you a total of 4 plus coats/leaving you with a very deep high gloss finish.

    • Areas are cleaned /we remove the masking paper/ pack up our equipment/ inspect the work.

    • New bead of caulk is applied/reinstall any hardware that was removed.

    • Care instructions handed out /any questions you may have are answered.

    • Please note that this process is for porcelain or tile fixtures. The process for fiberglass, Formica, cultured marble is very similar to this.

    Before We Arrive →

  • Before We Arrive

    Clean equals fast
    Please clear all surfaces and areas where work will be done and remove all items from tubs, showers and counters or areas which we will be working. The better the area is cleared the faster we can get the job done.

    Please move all furniture and items like paintings, vases, or any decorative (knick knacks) items 8-10 feet from work area. There may be an additional charge in some cases where there is an unusual amount of items that need to be protected.

    Tubs, showers and walls do not need to be cleaned before we arrive. Our process of cleaning and treating the surface will take care of the cleaning so you don’t have to.

    Overview ←Day of the Project →

  • Day of the Project

    NO PETS, NO EXCEPTIONS
    No people or pets/animals can be in the room we are reglazing (kitchen or bath) when we start the reglazing process and 4  hrs after we finish the work. If you have pets (cats, dogs, fish, turtles, etc) they too need to be out while we are working in the room. Sorry no exceptions.

    No one other than our company employees can be in the room while we are reglazing this is for you safety and our peace of mind. Sorry no exceptions.

    Please allow the area to air dry, ventilate for a minimum of five 4 hours before re-entry. People with respiratory conditions, allergies, or other medical issues may consider being out of the house for a minimum of 4 hours to avoid upset.

    Please make necessary arrangements. The item(s) being reglazed will be ready for use in as little as 12 hrs, we will let you know when it is safe to you use your newly reglazed bathtub.

    Please let us know about anything out of the ordinary that we need to know about before we get there to make like medical conditions, valuable items, special instructions for our technicians, wether your dog bites,etc.

    You will be amazed how quickly we can transform ugly to beautiful. Give us a call today 213-BATHTUB (213-228-4882)

    Before We Arrive ←Care & Maintenance →

  • Care & Maintenance

    Clean with Dish Washing Soap
    By following the guidelines listed below, you will be assured many years of trouble-free service.

    DO NOT use the surface for the time specified by us. Although the refinished surface can be put back into full use after this time, the surface will actually require up to 10 days to completely cure. Please observe the following:

    DO NOT use any abrasive cleaners on or near the refinished surface. Your new glossy finish is easily cleaned with any mild liquid cleanser. In general, any cleaner approved for use on acrylic surfaces is okay to us

    DO NOT use any abrasive scrubbing pads, such as ScotchBrite or any similar scrubbing pads, as this will scratch the new surface with repeated use.

    DO NOT drop sharp or heavy objects on the finish. Although porcelain and fiberglass tub are very sturdy dropping very heavy items could damage the surface.

    DO NOT have leaky faucets.They should be properly maintained by the owner and user, to protect the new surface. Leaky faucets may leave rust and hard water stains on the new finish.

    DO NOT Hair dyes or drain openers which may stain the new finish.  Introduction of any of these chemicals onto the finish would be considered neglect and possibly void any warranty given to you.

    DO NOTuse a rubber bath mat. We can apply a permanent non skid bottom (slightly extra charge) to the finish when we are reglazing. Rubber mats could be a safety hazard and are unsanitary.

  • DO NOT use abrasive cleansers. No S-O-S pads. No Comet. No razors. NO ABRASIVES AT ALL! The tub will clean easily with spray cleaners and a soft sponge. 
  • DO NOT let workers stand in a reglazed tub with their shoes on. Have them remove shoes & put a soft towel down.DO USE Lysol Tile Cleaner – Mr. Clean – Fantastic -Dow Scrub Free – Fantastic – Windex -Mr Clean -Dish Washing Soaps – Dawn – Joy – Ivory

    NO POWDERS, NO ABRASIVES like Ajax or Comet, just a soft sponge will do.

    REMEMBER, if you treat your new surface with respect, clean it regularly, and follow the above guidelines, your fixture will stay shiny and bright, and give you many years of trouble-free service.

    Day of the Project ←